AAI ORIGINAL English Verison N1201SA N1201SA+ 34.375MHz-2.7GHz UV RF Vector Impedance ANT SWR Antenna Analyzer Meter Tester
80
Direct purchase from the factory 
Zaručené bezpečné platby
Darček zdarma
Prepravná politika
Reklamačný poriadokDarček zdarma
Vitajte v Roymall, vašej profesionálnej webovej stránke na nákup prémiových darčekov. Veľmi si vážime a oceňujeme vašu podporu a chceme vám poďakovať tým, že pridáme extra nádej do vašich nákupov. Keď u nás nakupujete, nielenže získate vysokokvalitné produkty, ktoré zlepšia váš životný štýl, ale s každou objednávkou dostanete aj exkluzívny darček zdarma. Ste pripravení preskúmať našu kolekciu a nájsť svoje dokonalé darčeky? Prezrite si náš výber prémiových darčekov, zadajte svoju objednávku a tešte sa na radosť z vášho darčeka, ktorý príde spolu s vašou objednávkou.Prepravná politika
Po prijatí vašej objednávky budeme pracovať na tom, aby sme vám tovar doručili a zabezpečili, aby dorazil bezpečne. Podrobnosti o doručení budú uvedené v potvrdzovacom e-maile.Vo väčšine prípadov sú objednávky spracované do 2 dní. Za mimoriadnych okolností bude oneskorenie nasledovné: Ak zadáte objednávku v sobotu, nedeľu alebo počas sviatkov, bude oneskorená o 2 dni.Normálne to trvá 5-7 pracovných dní (pondelok až piatok), ak nie sú ovplyvnené meškaním letu alebo inými environmentálnymi faktormi.Pretože naša prepravná služba je celosvetová, dodacie lehoty závisia od vašej polohy, takže môže trvať niekoľko dní, a ak sa nachádzate v odľahlých oblastiach alebo krajinách, buďte prosím trpezliví.1. Politika vrátenia a výmeny
Akceptujeme iba položky zakúpené na roymall.com. Ak ste nakúpili od našich miestnych distribútorov alebo iných predajcov, nemôžete ich vrátiť na našej strane. Položky v konečnom predaji alebo darčeky zdarma nie je možné vrátiť.Aby ste mohli vrátiť tovar, musí byť nepoužitý a v rovnakom stave, v akom ste ho dostali. Musí byť tiež v pôvodnom balení.Po prijatí pokynov na vrátenie od nás zabalte vrátené položky a zanechajte balík na miestnej pošte alebo u iného prepravcu.Vašu vrátenú alebo vymenenú položku spracujeme do 3-5 pracovných dní po jej prijatí. Vrátenie peňazí bude spracované a pripísané automaticky na pôvodnú platobnú metódu.Nie je možné prijať vrátenie ani výmenu, ak bol produkt vyrobený na mieru, vrátane vlastnej veľkosti, farby alebo potlače.Potrebujete ďalšiu pomoc? Kontaktujte nás. service@roymall.com alebo Whatsapp: +86193598494712. Politika vrátenia peňazí
Po prijatí vráteného balíka a jeho kontrole dostanete úplné vrátenie peňazí alebo 100% kredit v obchode. Vrátenie peňazí bude spracované a pripísané automaticky na pôvodnú platobnú metódu.Upozorňujeme, že náklady na dopravu a akékoľvek clá alebo poplatky nie sú vratné. Dodatočné náklady na dopravu nie sú vratné po odoslaní balíka. Zodpovedáte za zaplatenie týchto poplatkov a my ich nemôžeme odpustiť ani vrátiť, aj keď sa objednávka vráti späť k nám.Ak máte akékoľvek problémy s procesom vrátenia peňazí, kontaktujte nás. service@roymall.com alebo Whatsapp: +8619359849471
Description:
- This instrument has four interfaces: single point measurement, scanning, system information, correction and calibration
The default boot into single-point measurement interface.
Note: For the convenience of the user, each time calibration correction options will automatically change to the user calibration. Meanwhile, in order to ensure the integrity of the calibration, the calibration process, the automatic shutdown function fails, the consistent boot.
Startup and shutdown:
Hold down the CTRL key off press the power switch button.
The boot state, long press (2S above) the switch button, after the release, the instrument will shut down
The boot state, long press (2S above) the switch button, after the release, the instrument will shut down
Recommend the use:
1, in order to ensure the accuracy of measurement and calibration, preheat the instrument at least 15 minutes.
2, try to use good quality RF cable and connectors.
3, calibrated cable marked to the next may not need to calibrate and direct use.
4, test cable process affect the measurement accuracy, it is recommended that, where possible, do not choose too long test cable.
5, measurement and calibration before, make sure you are not in a strong wireless signal, so as to avoid interference caused by inaccurate measurements.
6, if the impedance measurements themselves do not understand, you can refer to a vector network analyzer instructions and tutorials. This instrument is equivalent to a single-port vector network analysis
Specification:
working currency: 140MHz~2700MHz
stepped frequency: 1kHz
Display: 2.4inch TFT
resolution: 320*240(QVGA)
battery: 2000mAH(7.4Wh)
power consumption: <1.5W
charge current: 400mA
charge port: USB
Auto power off can be set 5-60minutes
Measured parameters:
resistence reactance standing wave s11
resolution ratio: 4 number
frequency accuracy: about 5ppm
Connector: SMA-K
Measurement range:
impedance: 0.1~1000
standing wave: 1.000~65
s11(dB): 0dB~-60dB
Working temperature: 0~40 degree
Package included:
1 x Original N1201SA Antenna Analyzer Meter
1 x English User Manual
- This instrument has four interfaces: single point measurement, scanning, system information, correction and calibration
The default boot into single-point measurement interface.
Note: For the convenience of the user, each time calibration correction options will automatically change to the user calibration. Meanwhile, in order to ensure the integrity of the calibration, the calibration process, the automatic shutdown function fails, the consistent boot.
Startup and shutdown:
Hold down the CTRL key off press the power switch button.
The boot state, long press (2S above) the switch button, after the release, the instrument will shut down
The boot state, long press (2S above) the switch button, after the release, the instrument will shut down
Recommend the use:
1, in order to ensure the accuracy of measurement and calibration, preheat the instrument at least 15 minutes.
2, try to use good quality RF cable and connectors.
3, calibrated cable marked to the next may not need to calibrate and direct use.
4, test cable process affect the measurement accuracy, it is recommended that, where possible, do not choose too long test cable.
5, measurement and calibration before, make sure you are not in a strong wireless signal, so as to avoid interference caused by inaccurate measurements.
6, if the impedance measurements themselves do not understand, you can refer to a vector network analyzer instructions and tutorials. This instrument is equivalent to a single-port vector network analysis
Specification:
working currency: 140MHz~2700MHz
stepped frequency: 1kHz
Display: 2.4inch TFT
resolution: 320*240(QVGA)
battery: 2000mAH(7.4Wh)
power consumption: <1.5W
charge current: 400mA
charge port: USB
Auto power off can be set 5-60minutes
Measured parameters:
resistence reactance standing wave s11
resolution ratio: 4 number
frequency accuracy: about 5ppm
Connector: SMA-K
Measurement range:
impedance: 0.1~1000
standing wave: 1.000~65
s11(dB): 0dB~-60dB
Working temperature: 0~40 degree
Package included:
1 x Original N1201SA Antenna Analyzer Meter
1 x English User Manual
- This instrument has four interfaces: single point measurement, scanning, system information, correction and calibration
The default boot into single-point measurement interface.
Note: For the convenience of the user, each time calibration correction options will automatically change to the user calibration. Meanwhile, in order to ensure the integrity of the calibration, the calibration process, the automatic shutdown function fails, the consistent boot.
Startup and shutdown:
Hold down the CTRL key off press the power switch button.
The boot state, long press (2S above) the switch button, after the release, the instrument will shut down
The boot state, long press (2S above) the switch button, after the release, the instrument will shut down
Recommend the use:
1, in order to ensure the accuracy of measurement and calibration, preheat the instrument at least 15 minutes.
2, try to use good quality RF cable and connectors.
3, calibrated cable marked to the next may not need to calibrate and direct use.
4, test cable process affect the measurement accuracy, it is recommended that, where possible, do not choose too long test cable.
5, measurement and calibration before, make sure you are not in a strong wireless signal, so as to avoid interference caused by inaccurate measurements.
6, if the impedance measurements themselves do not understand, you can refer to a vector network analyzer instructions and tutorials. This instrument is equivalent to a single-port vector network analysis
Specification:
working currency: 140MHz~2700MHz
stepped frequency: 1kHz
Display: 2.4inch TFT
resolution: 320*240(QVGA)
battery: 2000mAH(7.4Wh)
power consumption: <1.5W
charge current: 400mA
charge port: USB
Auto power off can be set 5-60minutes
Measured parameters:
resistence reactance standing wave s11
resolution ratio: 4 number
frequency accuracy: about 5ppm
Connector: SMA-K
Measurement range:
impedance: 0.1~1000
standing wave: 1.000~65
s11(dB): 0dB~-60dB
Working temperature: 0~40 degree
Package included:
1 x Original N1201SA Antenna Analyzer Meter
1 x English User Manual
- This instrument has four interfaces: single point measurement, scanning, system information, correction and calibration
The default boot into single-point measurement interface.
Note: For the convenience of the user, each time calibration correction options will automatically change to the user calibration. Meanwhile, in order to ensure the integrity of the calibration, the calibration process, the automatic shutdown function fails, the consistent boot.
Startup and shutdown:
Hold down the CTRL key off press the power switch button.
The boot state, long press (2S above) the switch button, after the release, the instrument will shut down
The boot state, long press (2S above) the switch button, after the release, the instrument will shut down
Recommend the use:
1, in order to ensure the accuracy of measurement and calibration, preheat the instrument at least 15 minutes.
2, try to use good quality RF cable and connectors.
3, calibrated cable marked to the next may not need to calibrate and direct use.
4, test cable process affect the measurement accuracy, it is recommended that, where possible, do not choose too long test cable.
5, measurement and calibration before, make sure you are not in a strong wireless signal, so as to avoid interference caused by inaccurate measurements.
6, if the impedance measurements themselves do not understand, you can refer to a vector network analyzer instructions and tutorials. This instrument is equivalent to a single-port vector network analysis
Specification:
working currency: 140MHz~2700MHz
stepped frequency: 1kHz
Display: 2.4inch TFT
resolution: 320*240(QVGA)
battery: 2000mAH(7.4Wh)
power consumption: <1.5W
charge current: 400mA
charge port: USB
Auto power off can be set 5-60minutes
Measured parameters:
resistence reactance standing wave s11
resolution ratio: 4 number
frequency accuracy: about 5ppm
Connector: SMA-K
Measurement range:
impedance: 0.1~1000
standing wave: 1.000~65
s11(dB): 0dB~-60dB
Working temperature: 0~40 degree
Package included:
1 x Original N1201SA Antenna Analyzer Meter
1 x English User Manual
